Rust 裸機開發：上午練習

指南針

(返回練習)

// Copyright 2023 Google LLC
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//      http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.

// ANCHOR: top
#![no_main]
#![no_std]

extern crate panic_halt as _;

use core::fmt::Write;
use cortex_m_rt::entry;
// ANCHOR_END: top
use core::cmp::{max, min};
use lsm303agr::{AccelOutputDataRate, Lsm303agr, MagOutputDataRate};
use microbit::display::blocking::Display;
use microbit::hal::prelude::*;
use microbit::hal::twim::Twim;
use microbit::hal::uarte::{Baudrate, Parity, Uarte};
use microbit::hal::Timer;
use microbit::pac::twim0::frequency::FREQUENCY_A;
use microbit::Board;

const COMPASS_SCALE: i32 = 30000;
const ACCELEROMETER_SCALE: i32 = 700;

// ANCHOR: main
#[entry]
fn main() -> ! {
    let board = Board::take().unwrap();

    // Configure serial port.
    let mut serial = Uarte::new(
        board.UARTE0,
        board.uart.into(),
        Parity::EXCLUDED,
        Baudrate::BAUD115200,
    );

    // Set up the I2C controller and Inertial Measurement Unit.
    // ANCHOR_END: main
    writeln!(serial, "Setting up IMU...").unwrap();
    let i2c = Twim::new(board.TWIM0, board.i2c_internal.into(), FREQUENCY_A::K100);
    let mut imu = Lsm303agr::new_with_i2c(i2c);
    imu.init().unwrap();
    imu.set_mag_odr(MagOutputDataRate::Hz50).unwrap();
    imu.set_accel_odr(AccelOutputDataRate::Hz50).unwrap();
    let mut imu = imu.into_mag_continuous().ok().unwrap();

    // Set up display and timer.
    let mut timer = Timer::new(board.TIMER0);
    let mut display = Display::new(board.display_pins);

    let mut mode = Mode::Compass;
    let mut button_pressed = false;

    // ANCHOR: loop
    writeln!(serial, "Ready.").unwrap();

    loop {
        // Read compass data and log it to the serial port.
        // ANCHOR_END: loop
        while !(imu.mag_status().unwrap().xyz_new_data
            && imu.accel_status().unwrap().xyz_new_data)
        {}
        let compass_reading = imu.mag_data().unwrap();
        let accelerometer_reading = imu.accel_data().unwrap();
        writeln!(
            serial,
            "{},{},{}\t{},{},{}",
            compass_reading.x,
            compass_reading.y,
            compass_reading.z,
            accelerometer_reading.x,
            accelerometer_reading.y,
            accelerometer_reading.z,
        )
        .unwrap();

        let mut image = [[0; 5]; 5];
        let (x, y) = match mode {
            Mode::Compass => (
                scale(-compass_reading.x, -COMPASS_SCALE, COMPASS_SCALE, 0, 4) as usize,
                scale(compass_reading.y, -COMPASS_SCALE, COMPASS_SCALE, 0, 4) as usize,
            ),
            Mode::Accelerometer => (
                scale(
                    accelerometer_reading.x,
                    -ACCELEROMETER_SCALE,
                    ACCELEROMETER_SCALE,
                    0,
                    4,
                ) as usize,
                scale(
                    -accelerometer_reading.y,
                    -ACCELEROMETER_SCALE,
                    ACCELEROMETER_SCALE,
                    0,
                    4,
                ) as usize,
            ),
        };
        image[y][x] = 255;
        display.show(&mut timer, image, 100);

        // If button A is pressed, switch to the next mode and briefly blink all LEDs on.
        if board.buttons.button_a.is_low().unwrap() {
            if !button_pressed {
                mode = mode.next();
                display.show(&mut timer, [[255; 5]; 5], 200);
            }
            button_pressed = true;
        } else {
            button_pressed = false;
        }
    }
}

#[derive(Copy, Clone, Debug, Eq, PartialEq)]
enum Mode {
    Compass,
    Accelerometer,
}

impl Mode {
    fn next(self) -> Self {
        match self {
            Self::Compass => Self::Accelerometer,
            Self::Accelerometer => Self::Compass,
        }
    }
}

fn scale(value: i32, min_in: i32, max_in: i32, min_out: i32, max_out: i32) -> i32 {
    let range_in = max_in - min_in;
    let range_out = max_out - min_out;
    cap(
        min_out + range_out * (value - min_in) / range_in,
        min_out,
        max_out,
    )
}

fn cap(value: i32, min_value: i32, max_value: i32) -> i32 {
    max(min_value, min(value, max_value))
}